TEGANGAN PRINSIPAL PADA CHASSIS MOBIL LISTRIK PROTOTYPE

Authors

  • Santoso Mulyadi Universitas Jember
  • Muh Nurkoyim Kustanto Universitas Jember
  • Cahya Alief Prasetyo Universitas Jember
  • Gaguk Jatisukamto Universitas Jember
  • Rika Dwi Hidayatul Qoryah Universitas Jember
  • Yuni Hermawan Universitas Jember
  • Mahros Darsin Universitas Jember

DOI:

https://doi.org/10.34128/je.v9i1.189

Keywords:

Chassis, Principal Stress, Electric Car

Abstract

An electric car is a vehicle that is driven by an electric motor, the electric motor obtains power from electricity stored in the battery. Chassis is an important component in electric cars. Chassis is part of an electric car that functions as a support system in an electric car. In the chassis there is a maximum and minimum stress called the principal stress. This principal stress becomes a reference to determine the safety of the chassis. So it is necessary to know the principal stress on the chassis. The testing process uses two drivers, each of which weighs 45 kg and 56 kg. The tests were carried out at three different points on the electric car chassis. From the results of the principal stress test, σ1 = 3.3282 MPa and σ2 = 1.5429 MPa for the 45 kg driver and σ1 = 3.8233 MPa and σ2 = 2.1123 MPa for the 56 kg driver. The principal stress on the chassis is still in a safe condition because it does not exceed the yield stress of the chassis material.

References

[1] Kurniawan, Anggi, “Analisis Kekuatan Struktur Crane Hook Dengan Perangkat Lunak Elemen Hingga Untuk Pembebanan 20 Ton”, Program Studi Teknik Mesin, Fakultas Teknik, Universitas Bengkulu, 2014.
[2] Fauzi, Helmi, “Analisis Tegangan Pada Frame Mobil Listrik Sinosi Menggunakan Metode Elemen Hingga”, Jurusan Teknik Mesin, Fakultas Teknik, Universitas Jember, 2013.
[3] Momon dan Astuti, Dwi, “Strategi Penurunan Emisi Gas Buang Kendaraan di Kota Padang”, Badan Penelitian dan Pengembangan Provinsi Sumatera Barat. Jurnal Kebijakan Pembangunan., Vol.15, No.1, 2020.
[4] Saputra, I Nyoman Adi., dkk, “Analisis Tegangan Statik Pada Rancang Frame Mobil Listrik Ganesha Sakti (Gaski) Menggunakan Software Solidworks 2014”, JJTM., Vol 6, No. 02, 2018.
[5] Isworo, Hajar dan Fauzan, Rahman, “Analisis Tegangan Pada Gripper Pencekam Botol Menggunakan Simulasi”, Program Studi Teknik Otomotif, Politeknik Hasnur. Jurnal Sains dan Terapan Politeknik Hasnur., Vol.03, No.02, 2015.
[6] Gere, J.M. dan Timoshenko, S.P., Mechanic of Material, Forth Edition, PWS Publishing Company, Terjemahan Suryoatmono, Bambang., Mekanika Bahan, Erlangga, Jakarta, 2000.
[7] Logan, Daryl L., A First Course in the Finite Element Method, ForthEdition, Thomson Canada Limited, Ontario, 2007.
[8] Mulyatno, Imam Puji., dkk, “Analisis Kekuatan Konstruksi Internal Ramp Sistem Steel Wire Rope Pada KM. Dharma Kencana VIII Dengan Metode Elemen Hingga, Jurnal Kapal Vol.11, No.02, 2014.

Additional Files

Published

2022-08-18

How to Cite

Mulyadi, S., Kustanto, M. N., Prasetyo, C. A., Jatisukamto, G., Qoryah, R. D. H., Hermawan, Y., & Darsin, M. (2022). TEGANGAN PRINSIPAL PADA CHASSIS MOBIL LISTRIK PROTOTYPE. ELEMEN : JURNAL TEKNIK MESIN, 9(1), 24–30. https://doi.org/10.34128/je.v9i1.189

Issue

Section

Articles