DESIGN OF A JAMU EXTRACT PRESSING TOOL USING A HYDRAULIC SYSTEM WITH A CAPACITY OF 2 KG

Authors

  • Bagas Subakti Rahmat universitas tidar
  • Rany Puspita Dewi Universitas Tidar
  • Herru Santosa Budiono Universitas Tidar

DOI:

https://doi.org/10.34128/je.v12i1.331

Keywords:

Jamu, Alat Press, Hidrolik, Simulasi statik

Abstract

The process of making herbal medicine still uses traditional methods for making herbal medicine. One of them is the process of squeezing herbal juice. The semi-automatic herbal juice press tool uses a hydraulic system with AISI 304 material. The results of designing the herbal juice press tool are the design of a press tool with a capacity of 2 kg and has dimensions of length 250 mm, width 250 mm, and height 250 mm. The load on static testing is 100 kg. The von Mises stress value in the frame is 38.23 MPa. The deformation value of the jamu juice press frame is 0.065. The smallest safety factor value for the jamu juice press frame is 5. The von Mises stress value for the jamu juice press tube is 21.057 MPa. The maximum deformation value of the jamu juice press tube is 0.017 mm. The smallest safety factor value for the herbal juice press tube is 9.735.

References

[1] S. Subaderi And O. Purnamayudhia, “Proses Produksi Jamu Tradisional Dengan Metode Network Planning,” J. Tecnoscienza, Vol. 6, No. 2, Pp. 264–276, 2022, Doi: 10.51158/Tecnoscienza.V6i2.669.

[2] C. T. Kurniawan And D. Suwito, “Pengembangan Desain Mesin Press Bahan Baku Jamu Dengan Metode Qfd (Quality Function Deployment),” Jptm, Vol. 08, No. 03, Pp. 158–164, 2019.

[3] G. Harunna, T. H. Ningsih, And A. P. Budiono, “Variasi Waktu Optimum Pengepressan Pada Mesin Press Jamu Yang Diproduksi Oleh Cv . Cahaya Berkah Gusti Tri Hartutuk Ningsih,” J. Tek. Mesin, Vol. 10, No. 02, Pp. 71–78, 2022.

[4] D. Ady, “Mesin Pres Semi Otomatis,” Univ. Sebel. Maret, 2010.

[5] A. Putriningtyas, N. F. Agustin, Pradhika, And A. P. K, “Pembuatan Mesin Press Hhidrolik Untuk Pengambilan Minyak,” 2007.

[6] M. Syaukani, F. Paundra, F. Qalbina, I. Dwi Arirohman, P. Yunesti, And Sabar, “Desain Dan Analisis Mesin Press Komposit Kapasitas 20 Ton,” J. Sci. Technol. Soc. Cult. , Vol. 1, No. 1, Pp. 29–34, 2021.

[7] F. Taufik Mazid, “Rancang Bangun Alat Pres Briket Sesai Design And Construction Of A Waste Briquette Pres,” Tek. Mesin, 2023.

[8] M. A. Suyuti, A. Z. Sultan, M. Ardiansyah, R. A. Mihdar, And G. Y. Swastika, “Rancang Bangun Automatic Press Tool Untuk Blanking Cetakan Kue,” J. Tek. Mesin Sinergi, Vol. 17, No. 2, Pp. 156–167, 2020, Doi: 10.31963/Sinergi.V17i2.2078.

[9] Setiyo Adi Nugroho, Daniel Rudjiono, And Febrian Rahmadhika, “Perancangan Identitas Perusahaan Dalam Bentukstationery Desain Di Rumah Kreasi Grafika,” Pixel J. Ilm. Komput. Graf., Vol. 14, No. 1, Pp. 48–57, 2021, Doi: 10.51903/Pixel.V14i1.456.

[10] A. Sai’in, B. Sumiyarso, R. T. Indrawati, And E. Saputra, “Analisis Kekuatan Rangka Mesin Pengolah Limbah Tulang Ikan Menjadi Bahan Dasar Pakan Ternak Berkapasitas 500 Kg/Jam Menggunakan Penggerak Motor Bensin 5,5 Hp,” J. Rekayasa Mesin, Vol. 17, No. 3, P. 435, 2022, Doi: 10.32497/Jrm.V17i3.3857.

[11] E. Prasetyo, R. Hermawan, M. N. I. Ridho, I. I. Hajar, H. Hariri, And E. A. Pane, “Analisis Kekuatan Rangka Pada Mesin Transverse Ducting Flange (Tdf) Menggunakan Software Solidworks,” Rekayasa, Vol. 13, No. 3, Pp. 299–306, 2020, Doi: 10.21107/Rekayasa.V13i3.8872.

[12] Aqshal And Nurato, “Analisis Perbandingan Faktor Keamanan Rangka Scooter,” J. Tek. Mesin, Vol. 09, No. 3, Pp. 164–172, 2020.

[13] M. A. Ficki, K. Kardiman, And N. Fauji, “Simulasi Beban Rangka Pada Mesin Penggiling Sekam Padi Menggunakan Perangkat Lunak,” Rotor, Vol. 15, No. 2, P. 44, 2022, Doi: 10.19184/Rotor.V15i2.32447.

[14] Moliza, Azhar, And S. Hardi, “Rancang Bangun Sistem Pengepresan Kaleng Minuman Otomatis Menggunakan Aktuator Pneumatik Berbasis Arduino Uno,” J. Tektro, Vol. 3, No. 1, Pp. 64–69, 2019.

[15] L. A. N. Wibawa, “Studi Numerik Pengaruh Radius Fillet Dan Ketebalan Cap Terhadap Tegangan Von Mises Dan Faktor Keamanan Silinder Berdinding Tipis Untuk Tabung Motor Roket,” J. Rekayasa Mesin, Vol. 15, No. 1, P. 1, 2020, Doi: 10.32497/Jrm.V15i1.1782.

Published

2025-06-28

How to Cite

Rahmat, B. S., Dewi, R. P., & Budiono, H. S. (2025). DESIGN OF A JAMU EXTRACT PRESSING TOOL USING A HYDRAULIC SYSTEM WITH A CAPACITY OF 2 KG. ELEMEN : JURNAL TEKNIK MESIN, 12(1), 45–52. https://doi.org/10.34128/je.v12i1.331

Issue

Section

Author guidelines

Most read articles by the same author(s)

Similar Articles

1 2 3 4 5 > >> 

You may also start an advanced similarity search for this article.