ANALYSIS OF SIKAFLEX-EPOXY MIXTURE ADHESIVE ON SHEAR TENSILE STRENGTH OF ALUMINIUM SINGLE LAP JOINT WITH SURFACE PATTERN VARIATIONS
DOI:
https://doi.org/10.34128/je.v11i2.293Keywords:
aluminium, epoxy-sikaflex, Aerodynamics, perekat, sambungan perekatAbstract
Vehicle construction requires strong joints to connect various materials. Many connections are made by welding, riveting, and adhesive bonding. Adhesive bonding has the advantages of efficiency, corrosion resistance, and ease of application. This research aims to analyze the effect of using sikaflex (SK) - epoxy (EP) mixed adhesive on the shear tensile strength of single lap joint aluminum. The material used was aluminum 5083 and sika flex and epoxy adhesives with an adhesive thickness of 0.4 mm, as well as variations in surface pattern treatment. The results showed that the highest tensile strength and modulus of elasticity in the variation of 10% SK: 90% EP with surface pattern 90º cross-type amounted to 2.34 MPa and 79.29 MPa. The highest strain was in the variation of 30% SK and 70% EP composition with a 0º horizontal surface pattern of 0.0466. The failure modes that occur are cohesive failure and thin-layer cohesive failure.
References
B. Widodo And A. Subardi, “Pengujian Sifat Mekanik Dan Struktur Mikro Aluminium Matrix Composite (Amc) Berpenguat Partikel Silikon Karbida (Sic) Dan Alumina (Al2o3),” 2019.
Suyitno, Bahan Teknik Untuk Rekayasawan (Logam Bukan Ferro). Yogyakarta: Pustaka Pranala, 2021.
F. Fasya And N. Iskandar, “Melt Loss Dan Porositas Pada Aluminium Hasil Daur Ulang,” 2015.
A. Setiawan, R. Riady, A. Program, S. T. Metalurgi, J. T. Pertambangan, And F. T. Mineral, “Pengaruh Proses Ageing Dan Powder Coating Pada Aluminium Profil Section 11309.” [Online]. Available: Www.Indiamart.Com
“Studi Eksperimental Pengaruh Suhu Pada Saat Curing Terhadap Kekuatan Geser Sturktur Makro Dan Mikro Pada Sambungan Logam Aluminium Dengan Adhesive Bonding”.
A. D. K. K. V Desai, Rohan P Chumble, “Modal Analysis Of An Adhesive Joint,” Int J Innov Res Sci Eng Technol, Vol. 04, No. 06, Pp. 4137–4145, Jun. 2015, Doi: 10.15680/Ijirset.2015.0406045.
M. D. Banea And L. F. M. Da Silva, “Adhesively Bonded Joints In Composite Materials: An Overview,” Jan. 01, 2009. Doi: 10.1243/14644207jmda219.
S. Hastuti Et Al., “Analisis Pengaruh Perekat Campuran Sikahyflex-Epoksi Terhadap Kekuatan Tarik Geser Pada Single Lap Joint Aluminium 5083-Komposit Cocofiber,” 2023. [Online]. Available: Https://Jurnal.Polines.Ac.Id/Index.Php/Rekayasa
J. Al Mahdi, S. Hastuti, X. Salahudin, R. Dwi Ardika, And S. R. Bintoro, “Pengaruh Ketebalan Perekat Epoksi-Lateks Terhadap Single Lap Joint Aluminium-Komposit,” Jurnal Crankshaft, Vol. 7, No. 1, 2024.
S. Hastuti And N. Sri Suharty, “Jurnal Teknologi Full Paper Joint Strength Of Mixed Silyl Modified Polymer-Epoxy Adhesive On Single Lap Joint Etched Aluminum,” 2017. [Online]. Available: Www.Jurnalteknologi.Utm.My
Iceecs 1. 2014$Denpasar, Institut Teknologi Bandung Sekolah Teknik Elektro Dan Informatika, Institute Of Electrical And Electronics Engineers Indonesia Section, International Conference On Electrical Engineering And Computer Science 1$Denpasar 2014.11.24-25, Iceecs 1$Denpasar 2014.11.24-25, And Ieee International Conference On Electrical Engineering And Computer Science 1$Denpasar 2014.11.24-25, Proceedings Of 2014 International Conference On Electrical Engineering And Computer Science (Iceecs) 24-25 November, Denpasar, Indonesia. Ieee, 2014.
“Sikaflex®-11 Fc.”
Dr. D. Kopeliovich, “Fundamentals Of Adhesive Bonding.”
P. I. Chen, K. Y. Wang, And H. H. Huang, “Strength And Failure Modes Of Adhesively Bonded Composite Joints With Easily Fabricated Nonflat Interfaces,” Compos Struct, Vol. 225, Oct. 2019, Doi: 10.1016/J.Compstruct.2019.111162.
S. Hastuti, X. Salahudin, C. Pramono, A. Akmal, N. Irsan, And A. Nurdin, “Analisis Kekuatan Adhesive Bonding Sambungan Tumpang Tunggal Aluminium 6063-Komposit Serat Sabut Kelapa,” 2023. [Online]. Available: Https://Jurnal.Polines.Ac.Id/Index.Php/Rekayasa.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2024 ELEMEN : JURNAL TEKNIK MESIN
This work is licensed under a Creative Commons Attribution 4.0 International License.
